Before powering on the server for the first time, insert the BIOS CR2032 battery into the connector on the motherboard.
Make sure to use the CR2032 battery format (20mm, 3 V), and don't worry about the manufacturer, as it is not crucial.
To determine the battery's polarity, follow these guidelines:
- If the battery lies horizontally on the motherboard (Neuro, UltraStation), the smooth side with the "+" symbol should face us.
- If the battery lies vertically (MiniNVR, DuoStation), check the battery holder to see which pole it should be facing.
After successfully installing the battery, proceed to configure the motherboard BIOS.
The following sections will include photos depicting the location of the BIOS battery and instructions on customizing the BIOS based on the specific model and serial number of your device.
Serial number of the NVR
The serial number is indicated on the sticker, which is located on the back of the NVR, on the side of the connectors as well as in the device datasheet.
Monitor Setup
For NeuroStation, UltraStation, and MiniNeuro servers, connect the monitor to the server's video card after installing the BIOS battery.
Note that breaking the sticker on the video card will not void the warranty.
Once the BIOS settings are completed, connect the monitor to the video connector on the motherboard.
Remember to perform all monitor switching actions while the server is turned off. Otherwise, you won't be able to see the display.
BIOS settings
Important!
Set the correct time and date in the BIOS. If this is not done, the server license will not be able to be loaded.
Serial: G24m1 / G25m1 / G25m2 / G25m5 / G25m8 / G27m2 / G27m5 / G27m8
Press F2 or DEL to enter the BIOS.
Configure the following parameters:
Switch to Advanced Mode by pressing F6.
- Advanced \ Chipset Configuration \ Primary Graphics Adapter = Onboard
- Advanced \ Chipset Configuration \ Restore on AC Power Loss = Power ON
- Advanced \ Chipset Configuration \ Above 4G Decoding = Disabled
- Boot \ Boot Option #1 = UEFI: ASX6000LNP-128GT-C
- Boot \ Full Screen Logo = Disabled
Save settings and exit (F10 and Yes)
Serial: G28c1 / G28c2 / G28c3* / G28c4
Press F2 or DEL to enter the BIOS.
Configure the following parameters:
Switch to Advanced Mode by pressing F6.
Advanced \ Integrated Graphics Configuration \ Initiate Graphic Adapter = IGD
Advanced \ Power Management Setup \ Restore after AC Power Lose = Power On
Boot \ Full Screen Logo Display = Disabled
Advanced \PCIe\ PCI Sub-system settings\pci_e3 and m2_2 switch = AUTO
Boot \ Boot Option #1 = UEFI:XPG SX6000 Lite 256GB M.2
*G28c3
Additionally, RAID battery installation is required, follow instructions for TRASSIR UltraStation.
Serial: H8m1 / H8m6 / H10m1 / H10m2
Press DEL to enter the BIOS.
Configure the following parameters:
- Advanced \ Boot Feature \ Restore on AC Power Loss = Power ON
- Boot \ Boot Mode Select = UEFI
- Boot \ Boot Option #1 = INTEL SSD... или UEFI Hard Disk
- Advanced\Chipset Configuration\System Agent (SA) Configuration\Graphics Configuration\Primary Dispaly = IGFX
- Advanced\Chipset Configuration\System Agent (SA) Configuration\Graphics Configuration\Internal Graphics = Enable
Save settings and exit (F4 and Yes)
RAID battery installation
If your server supports RAID, a battery will be required on the RAID controller. This will need to be purchased individually.
It looks like this: LSI 49571-15 rev c ("rev a" older version looks the same, you can use either one)
It must be connected to the battery power connector on the RAID controller.
Serial: E16m1 / E18m1
Press DEL to enter the BIOS.
Configure the following parameters:
Switch to Advanced Mode by pressing F7.
- Chipset \ North Cluster Configuration \ Primary Display = IGT
- Advanced \ ACPI Settings \ Restore on AC Power Loss = Power ON
- Boot \ Boot Option #1 = UEFI: ASX6000LNP-128GT-C
- Boot \ Full Screen Logo = Disabled
Save settings and exit (F10 and Yes)
Serial: E13m1 / E13m2
Press F2 to enter the BIOS.
Configure the following parameters:
- Setup \ Advanced \ Miscellaneous Configuration \ State After G3 – S0 State
- Boot \ Add Boot Options - First
- Boot \ EFI/Legacy Device Order - Legacy first
- Boot \ EFI - EFI - Configure the boot priority from Hard drive
Save settings and exit (F10 and Yes)
Serial: L11m1
Press F2 to enter the BIOS.
Configure the following parameters:
- Setup \ Advanced \ Miscellaneous Configuration \ State After G3 – S0 State
- Boot \ Add Boot Options - First
- Boot \ EFI/Legacy Device Order - EFI device first
- Boot \ EFI - Configure the boot priority from Hard Drive
Save settings and exit (F10 and Yes)